How to distinguish between Saigang and UPE
UPE is ultra-high molecular weight polyethylene with a density of about 0.88 g/cm3, and Saigang is a polyoxymethylene POM with a density of about 1.5 g/cm3. It can be distinguished by a similar volume and a hand. The most important one is Saigang, while the other is UPE. Please send inquiry and drawing to sales@honyplastic.com
What is the difference between plastic steel and Saigang
The main resin is different-Saigang is POM (polyoxymethylene), while the plastic steel is PVC (polyvinyl chloride). Please send inquiry and drawing to sales@honyplastic.com
Which is more wear-resistant, POM (Saigang) or brass (POM or brass wears faster)
If the two materials are rubbed against each other, of course, brass is more wear-resistant than POM. The hardness and melting point of POM are much lower than that of brass. POM is also unstable at high temperatures. The heat generated by friction will increase the temperature of the contact surface between the two. These conditions are naturally unfavorable for POM. Combining these few points, it can be seen that POM cannot grind brass. This problem should also consider other factors in the application, such as the size of the applied pressure, the environment, etc., because POM and br
What is the use of pom plastic
POM plastic (Polyoxymethylene) (Saigang~Trane) English name: Polyoxymethylene(Polyformaldehyde) A kind of synthetic resin, also known as polyoxymethylene resin, POM plastic, Saigang material, etc.; it is a kind of white or black plastic particles with high hardness, high rigidity and high wear resistance. Mainly used in gears, bearings, auto parts, machine tools, instrument internals and other products that play a role as skeletons. .It can replace most non-ferrous metals, automobiles, machine tools, instrument internals, bearings, fasteners, gears, springs, p
Definition of POM (polyoxymethylene resin): Polyoxymethylene is a linear polymer with no side chains, high density and high crystallinity. According to the different chemical structure in its molecular chain, it can be divided into two types: homopolyoxymethylene and copolyoxymethylene. The important difference between the two is that the density, crystallinity, and melting point of POM are high, but the thermal stability is poor, and the processing temperature range is narrow (about 10℃), the stability to acid and alkali is slightly lower; while the density, crystallinity, melting po
What material does PA and POM refer to?
POM has strong rigidity, which is alleged by Saigang. PA has good toughness, wear resistance and self-lubricity. Please send inquiry and drawing to sales@honyplastic.com
The difference between Saigang and Teflon
Color: Teflon (Teflon) is more moist, such as silk and milky white, while POM (Xigang) is harder in color. Feel: The hand feel is the same as the color. Teflon has a very smooth hand feel, and will not be sticky even at acute angles, while POM (saigang) and Teflon have the opposite feel. Please send inquiry and drawing to sales@honyplastic.com
What is the difference between the appearance of Teflon and Saigang
Color: The color of Teflon is relatively smooth, like the white of silk and milk, while the color of POM (Saigang) is more rigid. Hand feel: The same feeling as the color. The hand feel of Teflon is very round, even if it is an acute angle, it will not feel like a hand, while the hand feel of POM (Saigang) and Teflon are just the opposite. Please send inquiry and drawing to sales@honyplastic.com
Are POM and POM the same kind?
Saigang is the common name, and POM is also the abbreviation in English! All refer to the same material! The full name in Chinese is POM Please send inquiry and drawing to sales@honyplastic.com
How to do the machining of Saigang POM
POM is a thermoplastic engineering plastic with high melting point and high crystallinity. Due to the good characteristics of POM, it is very suitable for machining on automatic lathes, especially for the manufacture of precision parts. Saigang is a plastic material that is relatively easy to machine and does not require special treatment. Please send inquiry and drawing to sales@honyplastic.com
Material Saigang (pom for short), also known as Saigang, special steel. Therefore, it is obtained by polymerization of formaldehyde, etc. Please send inquiry and drawing to sales@honyplastic.com
Polyoxymethylene (pom) plastic is a linear polymer with no side chains, high density, high crystallinity, and good dielectric properties. You can judge your application based on the following data, if it is used as a busbar clamp, it should be ok. But pom has conductive materials, such as ds-01m of polyplastic company and n2320 of basf are conductive. item Item Homopolyoxymethylene Copolyoxymethylene Dielectric constant 50hz 3.7 3.8 103hz 3.7 3.8 106hz 3.7 3.7 Dielectric loss
Which material has good toughness, nylon or pom?
POM 1. High mechanical strength and rigidity; 2. Highest fatigue strength; 3. Environmental resistance and good resistance to organic solvents; 4. Strong resistance to repeated impact; 5. Wide temperature range (-40℃~120 ℃); 6. Good electrical properties; 7. Good recovery; 8. Self-lubricating and good wear resistance; 9. Excellent dimensional stability. Uses: Electronic appliances: washing machine, juicer timer and other components; automobile: handlebars, power windows and other parts; mechanical parts, gears, handles, screws, toys, etc.; Classification: glass fiber/carbon fiber rei
What is the hardness of POM steel material
The hardness of POM is 118-122R, and the hardness of different models is also different, and the hardness of each model of POM material is not very different! Please send inquiry and drawing to sales@honyplastic.com
How many years is the service life of POM (Saigang)
POM is easily oxidized by light, and the service life is relatively short, usually about 5 years Please send inquiry and drawing to sales@honyplastic.com
There are three types of POM 1. The normal type has no conductivity. 2: Conductive POM The conductivity coefficient is generally 10 to the power of 3 to 5. 3 Anti-static POM, anti-static coefficient 10 to the 6th to the 9th power. Good quality POM board: new material processing, uniform thickness, no bubbles, small deformation, smooth surface and bright luster. Inferior quality plates: add back material, phosphor (increase brightness), calcium carbonate (increase specific gravity), etc., with rough surface, uneven thickness, and pores. The anti-static POM coefficient is go
POM (polyoxymethylene) is a kind of thermoplastic engineering plastic with high melting point and high crystallinity that appeared in the 1960s. The working temperature ranges from minus 60 degrees to 100 degrees. Due to its high surface strength and smoothness, POM has excellent sliding properties and wear resistance. There is basically no tension in POM. It has high heat stability and chemical stability. Features: high mechanical strength, high rigidity, high hardness; excellent elasticity; good creep resistance; high impact strength even at low temperatures; very good dimensional sta
The difference between POM material and nylon material
The natural color of the dragon is ivory, and the natural color of POM is white. Polyoxymethylene plastic is another excellent resin variety developed after nylon, with excellent comprehensive properties. Polyoxymethylene has good resistance to solvents, oils, weak acids and weak alkalis. Polyoxymethylene has high hardness and rigidity, high resistance to creep and stress relaxation, excellent wear resistance, self-lubrication, and fatigue The scientific name of polyoxymethylene polyoxymethylene (POM) Polyoxymethylene is a linear polymer with no side chains, high de
Why is POM material called Saigang? What is the reason?
The main reason is that the hardness of POM is relatively high. The Rockwell hardness reaches D80-85Z, which is a high-hardness material in engineering plastics. In terms of hardness, it is comparable to steel, and in other processing properties. , POM is also good, making some spare parts, bearings, gears, etc., is also good. Nowadays, engineering plastics is an emerging industry, many of which can replace steel, and have properties that metal materials do not have, such as insulation, wear resistance, acid and alkali resistance, etc.
POM has high strength and rigidity, good elasticity, and good wear resistance. Its mechanical properties are excellent, the specific strength can reach 50.5MPa, and the specific stiffness can reach 2650MPa, which is very close to metal. The mechanical properties of POM change little with temperature, and the change of copolymerized POM is slightly larger than that of homopolymerized POM. The impact strength of POM is higher, but the conventional impact is not as good as ABS and PC; POM is sensitive to notches, which can reduce the impact strength by as much as 90%. The fatigue strength o
What is the difference between imported POM rods and domestic POM rods
Compared with the domestic POM, the imported POM rod has a purer material, less internal impurities, no pores inside the material, and stress relief. Please send inquiry and drawing to sales@honyplastic.com
Nylon was developed by the outstanding American scientist Carothers (Carothers) and a scientific research team under his leadership. It was the first synthetic fiber to appear in the world. The emergence of nylon has given a new look to textiles. Its synthesis is a major breakthrough in the synthetic fiber industry and a very important milestone in polymer chemistry. main products With the miniaturization of automobiles, the higher performance of electronic and electrical equipment, and the acceleration of the process of lightweight mechanical equipment, the demand for nylon will
How to process nylon rods with ordinary cars, and how fast is the speed?
Ordinary car fixtures are strong metal jaws, so you first need to consider auxiliary fixtures and center positioning (large parts processing can be ignored); The tool can be selected from high-speed steel tools, but the cutting tool's edge seems to be a bit technical (I remember it is the outer end face in a trance, I can't remember the entering angle, hehe, I won't do it for a long time); Coolant is necessary, otherwise the nylon rod will be deformed or damaged due to high temperature and heat during high-speed processing; The machining spindle speed seems to be abo
How to ensure the size when processing nylon materials on the machine
Water absorption will affect the size and accuracy of the parts to a certain extent, especially the thickening of thin-walled parts; water absorption will also affect the mechanical (strength, creep) and electrical properties of nylon materials due to the influence of water absorption. ,nylon Please send inquiry and drawing to sales@honyplastic.com
Tel: 86-852-34604012
Whatsapp: +86 18680371609
Address: FLAT/RM B 5/F GAYLORD COMMERCIAL BUILDING 114-118 LOCKHART ROAD WANCHAI HONGKONG, HONGKONG China Hong Kong
Website: https://www.honyplastic.com
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
