What is the difference between PA66 nylon material and MC901 nylon use
MC nylon is also called cast nylon. It uses the molten raw material caprolactam monomer C6H11NO as a catalyst with an alkaline substance as a catalyst, together with activators and other additives, to make the monomer to be polymerized, and it is directly injected and preheated to a certain level. In the temperature mold, the material will be polymerized quickly in the mold and condensed into a tough solid embryo, and then processed by the relevant process to obtain the predetermined product. As one of the engineering plastics, MC nylon products "replace steel with plastic and have excellent p
The main characteristics of nylon rod
High mechanical strength, stiffness, hardness, toughness, good aging resistance, good mechanical damping ability, good sliding properties, excellent wear resistance, good machining performance, when used for precise and effective control, no creeping phenomenon, anti-wear Good performance, good dimensional stability Please send inquiry and drawing to sales@honyplastic.com
Ordinary nylon has good mechanical properties and plasticity. It will be much better as long as you lightly hold it against the incoming car. However, it is impossible to ensure the straightness in the ideal state. It will definitely deform more or less, depending on how much you require! If you want to ensure that you are in the best condition, I suggest using nylon 66+30GF, which has good rigidity and has a lot more strength than ordinary nylon; please refer to the following information for your reference in detail: There are the following types of nylon 66: 1: Nylon 66
What are the models of imported nylon sheets
Imported plastic material series. Imported PEEK board 201311 What are the models of imported nylon sheets? 201308 Waterproof performance 201325 Brown gray PEEK111111-04 Please send inquiry and drawing to sales@honyplastic.com
What are the diameters of nylon rods
It is estimated that there are from 5 mm to 500 mm, and it also depends on the length of your processing Please send inquiry and drawing to sales@honyplastic.com
Are industrial nylon rods resistant to high temperatures?
Nylon rods cannot withstand high temperature 400 degrees There are modified plastics that can withstand high temperatures above 400 degrees, and there are coatings that can withstand high temperatures of 1800 degree Please send inquiry and drawing to sales@honyplastic.com
Nylon rods use: Nylon rods have good toughness, strong abrasion resistance, oil resistance, earthquake resistance, good tensile strength, good bending strength, low water absorption, good dimensional stability, etc., so they are used to process various wear-resistant high-strength parts. The product has a wide range of uses. It is a good material that replaces steel, iron, copper and other metals with plastic, and is an important engineering plastic; cast nylon widely replaces wear-resistant parts of mechanical equipment, and replaces copper and alloys as we
What is a nylon rod? What are its characteristics and functions
Nylon rod is an important engineering plastic, which can replace the wear-resistant parts of mechanical equipment, and replace copper and alloy as the wear-resistant parts of equipment. It has good toughness, strong abrasion resistance, oil resistance, earthquake resistance, good tensile strength, good bending strength, low water absorption, good dimensional stability, etc., so it is used to process various wear-resistant high-strength parts. It is suitable for the production of wear-resistant parts, transmission structural parts, household appliances parts, automobile manufacturing parts, scr
Polytetrafluoroethylene and nylon are two different plastics. PTFE is a special plastic, commonly known as the plastic king, and nylon is an engineering plastic, and the scientific name is polyamide. The performance and price of PTFE are much higher than nylon. These two kinds of plastics often appear in the form of a rod with an intermediate shape, which is mainly for the convenience of users to make various parts by mechanical processing methods. The PTFE rod is milky white, and the nylon rod is slightly yellow, which is easier to distinguish
Nylon 66+GF30 (black) Nylon 6 (white) and Nylon 66 (cream color)
Nylon 66+GF30 (black): Compared with pure nylon 66, this nylon is reinforced with 30% glass fiber, and its heat resistance, strength, rigidity, creep resistance, dimensional stability, abrasion resistance and other properties are all There is an improvement, and its maximum allowable use temperature is higher. Nylon 6 (white): This material has the most superior comprehensive properties, including mechanical strength, stiffness, toughness, mechanical shock absorption and wear resistance. These characteristics, coupled with good electrical insulation and chemical resistance, make nylon 6
What are the main materials of nylon rods commonly used in industry.
There are currently two main types of nylon rods commonly used in the industry: one is extrusion molding and the other is casting molding. The materials used for extrusion are mainly nylon 6, 66, 1010, 12, 11, 1212 and other materials, and MC nylon is commonly used for casting. According to different requirements, different materials of nylon are selected. Extrusion type: Among them, nylon 6 and 66 are ordinary nylons. Compared with long carbon chain nylon 1212, they have higher water absorption, lower abrasion resistance, higher hardness, better heat resistance, and lower low te
The main characteristics of nylon board
High mechanical strength, stiffness, hardness, toughness, good aging resistance, good mechanical damping ability, good sliding properties, excellent wear resistance, good machining performance, when used for precise and effective control, no creeping phenomenon, anti-wear Good performance, good dimensional stability Please send inquiry and drawing to sales@honyplastic.com
Nylon, the Chinese name of polyamide, and the English name of Polyamide (PA), is the general term for thermoplastic resins containing repeating amide groups-NHCO- on the main chain of the molecule. Its name is determined by the specific number of carbon atoms of the synthesized monomer Please send inquiry and drawing to sales@honyplastic.com
The difference between PVC board and nylon board
1. PVC: The chemical name is polyvinyl chloride, which is divided into rigid polyvinyl chloride and soft polyvinyl chloride. High mechanical strength, chemical properties Vinyl chloride (codenamed PVC) is a synthetic polymer formed by the polymerization of vinyl chloride monomer. Polyvinyl chloride is a white or light yellow powdery resin with a density of about 1.4 and a chlorine content of about 56% to 58%. Adding different plasticizers and stabilizers to the polyvinyl chloride resin can produce different rigid polyvinyl chloride and soft polyvinyl chloride. Polyvinyl chloride itself
Introduction of oily nylon board
Nylon board nylon (Nylon), Chinese name polyamide, English name Polyamide, PA for short. It is the general term for thermoplastic resins containing repeating amide groups-[NHCO]-on the main chain of the molecule. The name is determined by the specific number of carbon atoms of the synthesized monomer. It was invented by the famous chemist Carothers of DuPont, the largest chemical industry company in the United States, and his scientific research team. Nylon series are the most important engineering plastics. This product is widely used, covering almost every field, and is the most widel
Nylon rod is an important engineering plastic, which can replace the wear-resistant parts of mechanical equipment, and replace copper and alloy as the wear-resistant parts of equipment. It has good toughness, strong abrasion resistance, oil resistance, earthquake resistance, good tensile strength, good bending strength, low water absorption, good dimensional stability, etc., so it is used to process various wear-resistant high-strength parts. Xinwei nylon rods are excellent in material selection, have a wide range of applications, and have strong practicability Please send i
Nylon board Outstanding wear resistance: Its friction coefficient is usually 0.1-0.3, which is about 1/4 of phenolic plastic. 1/3 of Babbitt alloy, so it is a self-lubricating material. Good mechanical properties: Its surface hardness is large, and it has high tensile strength, bending strength and impact strength, and high ductility. Its compressive strength is comparable to that of metals, and its fatigue strength is equivalent to that of metal materials such as cast iron and aluminum alloy. Excellent chemical stability: It is not affected by chemicals such as wea
What are the areas of plexiglass, acrylic board, pp board, pc board, PTFE board, nylon board
Nylon board Outstanding wear resistance: Its friction coefficient is usually 0.1-0.3, which is about 1/4 of phenolic plastic. 1/3 of Babbitt alloy, so it is a self-lubricating material. Good mechanical properties: Its surface hardness is large, and it has high tensile strength, bending strength and impact strength, and high ductility. Its compressive strength is comparable to that of metals, and its fatigue strength is equivalent to that of metal materials such as cast iron and aluminum alloy. Excellent chemical stability: It is not affected by chemicals such as wea
The degree of wear resistance of nylon board relative to plasti
Nylon plates are divided into extrusion and casting according to different production processes. Extruded nylon sheet 1, nylon 6 (white): This material has the most superior comprehensive properties, including mechanical strength, stiffness, toughness, mechanical shock absorption and wear resistance. These characteristics, coupled with good electrical insulation and chemical resistance, make nylon 6 a "universal grade" material for the manufacture of mechanical structural parts and maintainable parts. 2. Nylon 66 (cream color): Compared with nylon 6, its mechanical strength, stiffness, h
The weight of the nylon board is calculated according to the density of the nylon board of different specifications. Nylon board has a history of more than one hundred years of development. Due to the rapid development of the chemical industry, nylon products have many varieties, and different nylon boards will have different densities. The density of nylon 66 is 1.14 to 1.15; the density of nylon 6 is 1.13 to 1.15; the density of nylon 11 is 1.04; the density of nylon 9 is 1.05; the density of MC nylon is 1.16. Under normal circumstances, the density of nylon is slightly higher
Nylon board, the material can be pa6 or pa66
Nylon board, the material can be pa6 or pa66 Nylon, the English name PolyAmide (PA), is the general name for polymers containing amide groups in the repeating units of the macromolecular backbone. Polyamides can be prepared by ring-opening polymerization of internal acid amines, and can also be obtained by polycondensation of diamines and dibasic acids. PA6, also known as nylon 6, is translucent or opaque milky white particles. It has the characteristics of thermoplasticity, light weight, good toughness, chemical resistance and good durability. It is generally used in auto parts, mechan
The advantages of nylon are: 1. High mechanical strength, good toughness, high tensile and compressive strength. The specific tensile strength is higher than that of metal, and the specific compressive strength is comparable to that of metal, but its rigidity is not as good as that of metal. The tensile strength is close to the yield strength, more than twice as high as ABS. The ability to absorb shock, stress and vibration is strong, and the impact strength is much higher than that of general plastics, and is better than acetal resin. 2. Outstanding fatigue resistance, the parts
What series are there for imported nylon plates and nylon rods?
What series are there for imported nylon plates and nylon rods? Extruded nylon series is the most important engineering plastic. This product is widely used, covering almost every field, and is the most widely used variety among the five major engineering plastics Please send inquiry and drawing to sales@honyplastic.com
Difference between nylon bar and PP bar
Just burn it with fire. The smell of nylon rod and PP rod is different, PP rod has a kind of wax burning smell, nylon has a kind of smell Please send inquiry and drawing to sales@honyplastic.com
Tel: 86-852-34604012
Whatsapp: 8618680371609
Address: FLAT/RM B 5/F GAYLORD COMMERCIAL BUILDING 114-118 LOCKHART ROAD WANCHAI HONGKONG, HONGKONG China Hong Kong
Website: https://www.honyplastic.com
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
