| Payment Type: | T/T,Paypal |
| Incoterm: | FOB,CFR,EXW,CIF,DDP,DDU |
| Min. Order: | 1 Kilogram |
| Transportation: | Ocean,Air,Express,Land |
| Port: | Shenzhen,Guangzhou,Hongkong |
Model No.: TECAST® T EF natural PA 6 C Bio-based
Brand: TECAST
| Selling Units | : | Kilogram |
| Package Type | : | Export package |
TECAST T EF natural (Bio-PA) is the environmentally friendly alternative to our conventionally manufactured cast nylon, TECAST T natural, and as a biopolymer part of our sustainable solutions.
The bio-based plastic is a molded polyamide (PA6C), and consists of a mass-balanced raw material. It therefore has an reduced CO2 footprint compared to the fossil version.
In terms of properties, the mass-balanced bioplastic is comparable to the fossil fuel based version, and is characterised in particular by good mechanical properties, along with excellent strength and wear properties. The PA6C bioplastic is often used as a substitute material for metals due to its lighter weight, and also exibits advantages over metals in terms of maintenance.
Ensinger produces the cast, biopolymer TECAST T EF natural in the form of PA6C tubes, PA6C plates and PA6C rods.
TECAST T EF natural is part of Ensinger's "Reuse for Tomorrow" solutions, which includes carefully developed products that contribute significantly to environmental protection through their reduced carbon footprint.
Facts
Chemical designation
PA 6 C (Cast polyamide 6)
Colour
ivory
Density
1.15 g/cm3
Main Features
from bio-based/ biomass-balanced raw materials with optimized PCF
good damping
good slide and wear properties
electrically insulating
high strength
good wear properties
resistant to many oils, greases and fuels
high toughness
Target industries
mechanical engineering
food technology
oil and gas industry
automotive industry
heavy duty industry
TECAST T EF natural PA 6 C Bio-based technical data sheet
| Mechanical properties | ||||
| Mechanical properties | Value | Unit | Parameter | Norm |
| Modulus of elasticity | 3500 | MPa | 1mm/min | DIN EN ISO 527-2 |
| (tensile test) | ||||
| Tensile strength | 83 | MPa | 50mm/min | DIN EN ISO 527-2 |
| Tensile strength at yield | 80 | MPa | 50mm/min | DIN EN ISO 527-2 |
| Elongation at yield (tensile test) | 4 | % | 50mm/min | DIN EN ISO 527-2 |
| Elongation at break (tensile test) | 40 | % | 50mm/min | DIN EN ISO 527-2 |
| Flexural strength | 109 | MPa | 2mm/min, 10 N | DIN EN ISO 178 |
| Modulus of elasticity | 3200 | MPa | 2mm/min, 10 N | DIN EN ISO 178 |
| (flexural test) | ||||
| Compression modulus | 2900 | MPa | 5mm/min, 10 N | EN ISO 604 |
| Compression strength | 19/36/83 | MPa | 1% / 2% / 5% | EN ISO 604 |
| Impact strength (Charpy) | n.b. | kJ/m2 | max. 7,5J | DIN EN ISO 179-1eU |
| Notched impact strength (Charpy) | 4 | kJ/m2 | max. 7,5J | DIN EN ISO 179-1eA |
| Shore hardness | 83 | D | DIN EN ISO 868 | |
| Thermal properties | ||||
| Thermal properties | Value | Unit | Parameter | Norm |
| Glass transition temperature | 40 | C | DIN EN ISO 11357 | |
| Melting temperature | 215 | C | DIN EN ISO 11357 | |
| Heat distortion temperature | C | HDT, Method A | ISO-R 75 Method A | |
| Thermal conductivity | 0.38 | W/(k*m) | ISO 22007-4:2008 | |
| Specific heat | 1.7 | J/(g*K) | ISO 22007-4:2008 | |
| Service temperature | 170 | C | short term | NN |
| Service temperature | 100 | C | long term | NN |
| Thermal expansion (CLTE) | 12 | 10-5*1/K | 23-60°C, long. | DIN EN ISO 11359-1;2 |
| Thermal expansion (CLTE) | 12 | 10-5*1/K | 23-100°C, long. | DIN EN ISO 11359-1;2 |
| Electrical properties | ||||
| Electrical properties | Value | Unit | Parameter | Norm |
| surface resistivity | 1014 | Ω | DIN IEC 60093 | |
| volume resistivity | 1014 | Ω*cm | DIN IEC 60093 | |
| Dielectric strength | kV/mm | DIN 53483-1 | ||
| Other properties | ||||
| Other properties | Value | Unit | Parameter | Norm |
| Resistance to hot water/ bases | (+) | - | - | |
| Flammability (UL94) | HB | - | corresponding to | DIN IEC 60695-11-10; |
| Resistance to weathering | - | - | - | |
| Water absorption | 0.2 - 0.4 | % | 24h / 96h (23°C) | DIN EN ISO 62 |
| Water absorption | % | saturation (23°C) | DIN EN ISO 62 | |
Tel: 86-852-34604012
Whatsapp: +8618680371609
Address: FLAT/RM B 5/F GAYLORD COMMERCIAL BUILDING 114-118 LOCKHART ROAD WANCHAI HONGKONG, HONGKONG China Hong Kong
Website: https://www.honyplastic.com
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Contact Now