HONYPLAS PEEK BLACK PEEK sheet

HONYPLAS®PEEK (abbreviation for PolyEtherEtherKetone) is a high performance semi-crystalline, engineering thermoplastic.PEEK is used in some of the toughest plastic applications that require the tightest tolerances. These include medical device parts, medical implants, structural applications, ultra-high vacuum applications, valve seats, pump gears, high purity seals, electrical connectors, screws, impellers, wear blades, lab equipment, analytical equipment, columns, cable insulation, and more.

HONYPLAS®PEEK is manufactured may use Victrex® PEEK 450G or ZYPEEK® 550G polymer. Strong, stiff plastic with outstanding chemical resistance; performs over a wide range of temps

PEEK PERFORMANCE

Properties of PEEK plastic include high temperature performance, excellent wear properties, superior chemical resistance and outstanding toughness and strength. It also has excellent deformation under load characteristics, a high flexural modulus, and exhibits low smoke and toxic gas emissions when exposed to a flame.

MACHINING PEEK

In its solid state, PEEK is readily machinable by CNC milling machines and is commonly used to produce high-quality plastic parts that are thermostable and both electrically and thermally insulating. PEEK is often considered a superior high-end engineering plastic, in the same category as Delrin, PTFE or nylon.

PEEK GRADES

General-purpose grade PEEK is unreinforced and offers the highest elongation and toughness of all PEEK grades. It is a strong and stiff plastic material that is often used in applications where performance at elevated temperatures is required, such as autoclaving. Peek meets Mil P 46183. It can be used continuously to 480°F (250°C) and in hot water or steam without permanent loss in physical properties.

FDA APPROVAL

Unfilled PEEK has been approved by the FDA for food contact applications.

PEEK COLORS

PEEK is naturally a very light brown or tan color as displayed in our images below, and is also available in black. Since it is an engineering plastic, color variations may occur between batches.

PEEK plastic sheets are the perfect choice for any high-tolerance, high-heat, chemical resistant plastic requirements, no matter how large or small!

The excellent performance of PEEK material is mainly manifested in the following aspects:

1. High temperature resistance

PEEK has a high glass transition temperature and melting point (334°C), which is one of the reasons why it can be reliably used in applications requiring heat resistance. Its load thermal deformation temperature is as high as 316℃, and its continuous use temperature is 260℃.

2. Mechanical characteristics

PEEK is a plastic with a balance between toughness and rigidity. In particular, its excellent fatigue resistance to alternating stress is the most outstanding among all plastics, comparable to alloy materials.

3. Self-lubricating

PEEK has outstanding sliding properties among all plastics, and is suitable for applications that strictly require low friction coefficient and abrasion resistance. In particular, the self-lubricating performance of PEEK modified with carbon fiber and graphite in a certain proportion is better.

4. Chemical resistance (corrosion resistance)

PEEK has excellent chemical resistance. Among ordinary chemicals, only concentrated sulfuric acid can dissolve or destroy it. Its corrosion resistance is similar to that of nickel steel.

5. Flame retardancy

PEEK is a very stable polymer. Samples with a thickness of 1.45mm can reach the highest flame retardant standards without adding any flame retardants.

6. Peel resistance

PEEK has good peel resistance, so it can be made into thin-covered wires or magnet wires, and can be used under harsh conditions.

7. Fatigue resistance

PEEK has the best fatigue resistance of all resins.

The more mature applications of HONYPLAS®PEEK include: piston ring, thrust ring, choke ring, valve disc, bacteria valve, star wheel, sealing ring, ball valve seat, bearing cage, oil-free lubrication bearing, magnetic pump of air compressor Isolation sleeves, electrodes, gears, screws, magnet wires, radiation shields, microwave digestion tanks, wafer carriers, etc.

HONY Plastic molding processing polyether ether ketone (PEEK) pipes, rods, plates, machining finished parts, injection molding polyether ether ketone (PEEK) products of various specifications, providing polyether ether ketone (PEEK) modified pellets .HONYPLAS®PEEK modified carbon fiber reinforced polyether ether ketone, glass fiber reinforced polyether ether ketone, polytetrafluoroethylene modified polyether ether ketone, graphite, molybdenum disulfide, etc. filled polyether ether ketone, respectively Various molding processes such as molding, injection molding, extrusion, powder spraying, blow molding, rotation, and melt spinning are carried out.

HONYPLAS®PEEK has been widely used in many fields such as petrochemical, electronic and electrical, instrumentation, machinery and automobiles, medical and health, aerospace, military nuclear energy, etc.

HONYPLAS®PEEK Product grade: 

1.HONYPLAS®PEEK Virgin : Brown-gray, made of pure polyether ether ketone resin as raw material, has good toughness and impact resistance among all PEEK grades. Pure PEEK can be sterilized using convenient sterilization methods (steam, dry heat, ethanol and Y-ray), and the raw material composition of PEEK complies with EU and US FDA regulations on food compliance, making it suitable for medical, pharmaceutical and food processing industry.

2.HONYPLAS®PEEK PTFE: Black, the result of adding PTFE, graphite and carbon fiber, makes it a bearing-grade plastic, its superior friction performance (low friction coefficient, wear resistance, higher peak pressure limit) .

3.HONYPLAS®PEEK 30GF: Brown-gray, the material is filled with 30% glass fiber reinforced plastic, which has better rigidity and creep resistance than pure PEEK, and better dimensional stability. It is the best choice for manufacturing structural parts. Can withstand a fixed load for a long time at high temperatures

4.HONYPLAS®PEEK 30CF: Black, this material is filled with 30% carbon fiber reinforcement, has better mechanical properties (higher elastic modulus, mechanical strength and creep) and more wear resistance than PEEK 30GF, and carbon fiber reinforced plastic is better than unreinforced plastic PEEK's plastic has 3.5 times the thermal conductivity to dissipate heat from the bearing surface faster

         HONYPLAS®PEEK Virgin                       HONYPLAS®PEEK PTFE                 HONYPLAS®PEEK 30GF               HONYPLAS®PEEK 30CF         

HONYPLAS®PEEK Product Technical Properties Data Sheet

PEEK rods produced by the continuous extrusion process are more suitable for small batches and large-scale products to be produced by machining. PEEK rods with a diameter of 5-250mm can be extruded, and the length is generally 1000 or 2000 or 3000, can also be cut according to customer requirements, there are nearly a hundred kinds of extrusion dies with diameter specifications, and the inventory is complete

HONYPLAS®PEEK Rod Size

HONY introduced imported PEEK profile extrusion production line to extrude 1250mm wide PEEK sheet to meet the demand of large-size PEEK parts in valve and other industries for ultra-wide PEEK sheet, better improve production efficiency and improve the quality of PEEK products. At the same time, the material utilization rate of the wide plate is very high when the typesetting cutting machine is processed.

HONYPLAS®PEEK Sheet Size

Our Test