ASIC Accessories

Mining machine accessories are tools or components that can assist the normal operation of the mining machine. There are many of them, including: power cable, fan control board, host device power supply, which is used to convert the voltage. This is a must-have accessory for the mining machine. Some of them are relatively Large mining machine manufacturers can give matching power supplies as gifts when purchasing mining machines. In addition, cables, fans, and control boards are all mining machine maintenance accessories. If the original device is damaged, the fan and control board can be used as replacements. The host device is usually a personal computer or a Raspberry Pi, which is only used to set up the mining machine startup, and the mining machine can also be used for other purposes after the mining machine is started.

Which is better, PC mining machine power supply or ordinary power supply?

PC mining machine power supply and ordinary power supply are better than PC mining machine power supply, because PC mining machine power supply is more durable and more professional, hope this answer can help you

Miner power supply general life
The life of the power supply depends on the quality of the components in the power supply and the conditions of use. Normally, a good power supply can work 12 hours a day for 5-6 years without any problem! So don't cause man-made damage, be careful not to start and shut down the computer frequently, keep the power supply in good heat dissipation, and clean the dust regularly.

What topology is used for the mining machine power supply
forward topology. In the mine, the power supply on the mine uses the forward topology power supply. Generally, the forward topology power supply is used in mines with high power or in the occasion of multiple outputs, and the output transient control of the forward topology power supply is better. Safe, high output rate.

How big is the power supply of the mining machine?
According to the size of the mining machine. If the load is a motor, light bulb or capacitive load, and the current is large at the moment of power-on, an appropriate power supply should be selected to avoid overload. If the load is a motor, consider voltage reversal at shutdown.

The power supply of the mining machine is fried because of what
Temperature is too high. The short circuit or overweight of the load leads to overheating, internal self-excitation of the power supply, excessive input voltage, failure of no-load protection, failure of output protection, and high frequency of the power supply. If it is a commercial machine, it is unlikely that there is a quality problem with the internal components.

How to forcibly power on the power supply of Innosilicon T3 ten mining machine
Miner power supply. It can be powered by plugging the cord into the power supply. Before repairing the faulty power supply, use the voltage measurement method to power on to determine whether the power supply has voltage output, test that the fan with voltage output does not turn, and use a multimeter to measure the fan port. If there is 12V voltage, it means that the output voltage is normal, just replace the same type of fan directly.

What power cord is used for the E10 miner?
The E10 miner needs to use NYPTJ138A power cord. The E10 mining machine has relatively high requirements on the power cord, and the NYPTJ138A power cord must be used to work normally.

Is the mining machine power supply the same as the computer power supply?
Hello friend. The power supply of the mining machine uses power electricity. It is 380 volts. The computer uses civilian electricity, which is 220 volts. They are not the same. Agree with my point of view, please adopt, thank you.

How many watts of power does the 8-card 1660s mining machine use?
The eight-card mining machine 1660s consumes about 750 watts per hour, which is about 0.75 kWh. The power supply is not outputting at full capacity all the time, but supplies power according to the demand. Now 1080 single card is 180w, and six of them are running at 100%, which is 1080w, and the superposition of other hardware power consumption is enough. But I only heard that the demand for machines to crack passwords is so high.

How to change the power output line of the mining machine
A power cord is required. To replace the power output line of the mining machine, you need to buy a CPU power supply line. Cut off the CPU power supply line of the original power supply and connect it with a new one. Just seal the wiring port with insulating tape.